100% Free D-PST-DY-23 Exam Dumps Use Real PowerStore Deploy Dumps With 220 Questions!
Pass Your D-PST-DY-23 Exam Easily With 100% Exam Passing Guarantee [2025]
NEW QUESTION # 24
When manually migrating a volume between PowerStore appliances, in what order should the tasks be carried out?
- A. 1. Select a volume and then select Migrate
2. Select destination appliance and then start migration
3. Rescan the Hosts
4. Select migrate now - B. 1. Rescan the Hosts
2. Select destination appliance and then start migration
3. Select a volume and then select Migrate
4. Select migrate now - C. 1. Select a volume and then select Migrate
2. Select migrate now
3. Select destination appliance and then start migration
4. Rescan the Hosts - D. 1. Rescan the Hosts
2. Select migrate now
3. Select a volume and then select Migrate
4. Select destination appliance and then start migration
Answer: A
NEW QUESTION # 25
Which type of network is used for storage migration between appliances?
- A. Intra-Cluster Data network
- B. Storage network
- C. Intra-Cluster Management network
- D. Inter-node network
Answer: A
NEW QUESTION # 26
SIMULATION
An administrator must configure a new protection policy for an existing VM with the following parameters.
Rule Name: 2x5x14
Days: M-F
Every: 12 Hours
Retention: 14 Days
Access Type: Snapshot
Policy
Name: Bronze
Snap Rule: 2x5x14
Apply the policy to VM1.
When you have finished continue to the next question.
Answer:
Explanation:
See explanation below
Explanation:
NEW QUESTION # 27
Refer to the Exhibit.
Note the yellow arrow. A Data Center Engineer notices that the LED is blinking blue and amber alternating at one second intervals.
What does this indicate?
- A. Node in Service Mode
- B. System not initialized
- C. Node is Degraded
- D. System is booting
Answer: A
NEW QUESTION # 28
During the discovery step of implementation, an unconfigured PowerStore is unavailable.
Which firewall ports must be open for a successful discovery?
- A. TCP port 8443 and UDP port 5353
- B. TCP port 80 and UDP port 80
- C. TCP port 5353 and UDP port 5353
- D. TCP and UDP ports 443 and 80
Answer: C
Explanation:
To properly discover a Dell PowerStore appliance using the Discovery Utility, you need to ensure that the following ports are open: TCP/UDP 5353: This port is used for mDNS (Multicast DNS) which is the protocol used by the PowerStore Discovery Utility to locate unconfigured PowerStore appliances. mDNS is essential for the appliance discovery process. (Grok 2) mDNS (Multicast DNS): PowerStore uses mDNS for discovery, especially when the array is unconfigured. mDNS allows devices to discover each other on a local network without needing a pre-configured DNS server. This is essential for the initial setup and discovery of a new PowerStore system.
Port 5353: This is the standard port used for mDNS communication. Both TCP and UDP port 5353 need to be open for mDNS to function correctly.
NEW QUESTION # 29
SIMULATION
Use the simulator to create an SMB NAS server using the following information:
* NAS and SMB computer name: payrollserver
* Network interface: BaseEnclosure-bond1
* IP address: 192.168.2.20
* Subnet: /24
* Gateway: 192.168.2.254
* VLAN: 1504
* AD/DNS: 192.168.2.50
* Windows domain name: company.com
* Domain administrator credentials: Administrator/password
When you have finished continue to the next question.
Answer:
Explanation:
See the Explanation below for complete solution
Explanation:
1. Open the simulator and log in with the default credentials: admin/Password123#.
2. SelectStorage>NAS Serversfrom the left menu.
3. Click+ CREATEto launch the Create NAS Server wizard.
4. Enterpayrollserveras the NAS and SMB computer name and clickNext.
5. SelectBaseEnclosure-bond1as the network interface and clickNext.
6. Enter192.168.2.20as the IP address,/24as the subnet,192.168.2.254as the gateway, and1504as the VLAN ID. ClickNext.
7. SelectJoin a Windows domainas the SMB server type and clickNext.
8. Enter192.168.2.50as the AD/DNS server,company.comas the Windows domain name,Administratoras the domain administrator username, andpasswordas the domain administrator password. ClickNext.
9. Review the summary and clickFinishto create the SMB NAS server.
NEW QUESTION # 30
What mechanism does PowerStore use to apply and manage licenses?
- A. SNMP traps
- B. USB drives
- C. PowerStore License Manager
- D. QR codes
Answer: C
NEW QUESTION # 31
Refer to the exhibit.
Which SMB path is used to access the share from client side?
- A. \\nas-smb07.hmarine.test\ Hmarine_Sales
- B. \\nas-smb07.hmarine test\SMB-FS07\ Hmarine_Sales
- C. \\SMB-FS07\Sales\Hmarine_Sales
- D. \\SMB-FS07\Hmarine_Sales
Answer: A
NEW QUESTION # 32
What does setting the alert threshold to 0 (zero) do when configuring replication rules?
- A. Enables alerts if the RPO cycle was missed for three consecutive cycles.
- B. Generates an alert if the synchronization time exceeds the RPO.
- C. Generates an alert if the data saved during the RPO cycle exceeds 20% of the storage object capacity
- D. Disables all alerts for any missed RPO cycles.
Answer: B
Explanation:
Here's a breakdown of how the alert threshold works in PowerStore replication:
RPO (Recovery Point Objective): The RPO defines the maximum acceptable amount of data loss in case of a disaster. It essentially determines how often data is replicated. For example, an RPO of 1 hour means you're willing to lose up to 1 hour's worth of data.
Alert Threshold: This setting allows you to control when PowerStore generates an alert if replication isn't meeting the defined RPO. It's the amount of time the system waits before raising an alert when a replication session fails to meet the RPO.
Threshold 0: When you set the alert threshold to 0, it means that PowerStore will immediately generate an alert if the synchronization time for a replication session takes longer than the RPO. This provides immediate notification of potential issues with replication performance or network connectivity.
Why other options are incorrect:
A . Disables all alerts for any missed RPO cycles: This is incorrect. Setting the threshold to 0 actually makes the system more sensitive to missed RPOs.
B . Generates an alert if the data saved during the RPO cycle exceeds 20% of the storage object capacity: This is not related to the alert threshold setting.
C . Enables alerts if the RPO cycle was missed for three consecutive cycles: The alert threshold doesn't have a built-in mechanism for consecutive missed cycles. It triggers an alert based on the synchronization time exceeding the RPO.
By setting the alert threshold to 0, you ensure that you're immediately notified of any replication delays, allowing you to take corrective action to prevent potential data loss.
NEW QUESTION # 33
Place the steps in the correct order to map a PowerStore volume to a NVMe host.
Answer:
Explanation:
Explanation:
NEW QUESTION # 34
Which network is used by the PowerStore for communication to the cluster database?
- A. ICM
- B. ICD
- C. IDN
- D. inter-node
Answer: A
NEW QUESTION # 35
What is the benefit of implementing multipathing in a PowerStore environment?
- A. Enhancing power efficiency
- B. Reducing the need for licenses
- C. Automating system updates
- D. Increasing network bandwidth and redundancy
Answer: D
NEW QUESTION # 36
A storage administrator has configured a VNX2 as a remote system.
Which Import External Storage migration architectural components are now established?
- A. Host Fibre Channel initiators are deregistered on the VNX2 storage system.
- B. Host iSCSI initiators are registered on the VNX2 storage system.
- C. Data path and management control path to the source storage system.
- D. Data path and management control path to the access host.
Answer: C
Explanation:
Topic 1,
SIMULATION / Lab Based Questions
NEW QUESTION # 37
Which protocol is commonly used to provide ESXi host access to vVols in PowerStore environments?
- A. vSAN
- B. iSCSI
- C. vVols
- D. NFS
Answer: C
NEW QUESTION # 38
Which component is responsible for managing the access of hosts to storage resources in PowerStore?
- A. Data node
- B. Network switch
- C. Storage processor
- D. Host initiator
Answer: C
NEW QUESTION # 39
......
The Dell PowerStore solution is a leading-edge storage platform that offers next-generation data storage capabilities, including unified storage, storage virtualization, and advanced data management. With the Dell PowerStore Deploy 2023 certification, IT professionals can demonstrate their expertise in this technology and enhance their career prospects in the field of data storage and management.
EMC D-PST-DY-23 exam is a vendor-specific exam, which means that it is designed to test the candidate's knowledge of Dell PowerStore Deploy 2023 only. D-PST-DY-23 exam consists of multiple-choice questions, and the passing score is 63%. D-PST-DY-23 exam is available in English, Japanese, and Chinese.
Study resources for the Valid D-PST-DY-23 Braindumps: https://www.passreview.com/D-PST-DY-23_exam-braindumps.html
D-PST-DY-23 Dumps are Available for Instant Access: https://drive.google.com/open?id=1PJGd-wLgyZ60g97bwmL9llK_6iA4PulO