A Fully Updated 2024 300-615 Exam Dumps - PDF Questions and Testing Engine
Easy Success Cisco 300-615 Exam in First Try
NEW QUESTION # 121
Refer to the exhibit.
An administrator directly connects a Fibre Channel storage array to ports 1 through 4 on a Cisco UCS 6454 Fabric Interconnect. The administrator configures a service profile to boot directly from the new Fibre Channel storage array, but the service profile fails to boot. When the administrator checks the output of the show flogi database command on the fabric interconnect, it shows the output presented in the exhibit. Which action resolves the issue?
- A. Configure the fabric interconnects in Fibre Channel switch mode.
- B. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Multiple Target.
- C. Configure the Zoning Type in vHBA Initiator Group as Multiple Initiator Single Target.
- D. Configure the fabric interconnects in Fibre Channel end-host mode
Answer: A
NEW QUESTION # 122
An engineer must place a Cisco UCS B-Series Server in a single server pool in Cisco UCS Manager.
The engineer creates a qualification policy, but the server is still seen in multiple pools.
Which two actions resolve the issue? (Choose two.)
- A. Set the storage capacity qualifier inside the Server Poo. Policy Qualification.
- B. Select the Server Pool Policy from the qualification drop-down menu in the Server Pool Policy Qualification
- C. Set the number of vNICs qualifier inside the Server Pool Policy.
- D. Set the operating system qualifier inside the Server Pool Policy Qualification
- E. Select the Server Pool Policy Qualification from the qualification drop-down menu in the Server Pool Policy
Answer: D,E
NEW QUESTION # 123
Which control plane is used according to this output?
- A. flood-and-learn IP address learning
- B. VXLAN OAM
- C. flood-and-learn MAC address learning
- D. BGP EVPN
Answer: D
NEW QUESTION # 124
Refer to the exhibit.
A network engineer needs to capture traffic from the VMs that utilize the IOM host interface Eth1/1/23 of a Cisco UCS B-Series chassis. A traffic analyzer is used to get traffic captured from the Eth1/4 interface of the subordinate fabric interconnect. The network engineer notices that traffic is not captured on the traffic analyzer. Which action resolves the issue?
- A. Span the traffic from the Eth 1/4 of the primary fabric interconnect.
- B. Span the traffic from the Eth 1/2 of the subordinate fabric interconnect.
- C. Span the traffic from the Eth 1/2 of the primary fabric interconnect.
- D. Span the traffic from the Eth 1/4 of the subordinate fabric interconnect.
Answer: A
NEW QUESTION # 125
A system administrator connects a Cisco Nexus 2248PQ FEX to a fabric interconnect to expand the ports that are available for connecting Cisco UCS C-Series Rack Servers. In Cisco UCS Manager, the administrator does not see the servers connected to this FEX. Which action should be taken to resolve the issue?
- A. The fabric interconnects must be rebooted before the FEX is recognized
- B. The ports that connect the FEX to the fabric interconnects must be configured as server ports
- C. The transceivers must be exchanged to support the connectivity between the FEX and the fabric interconnects
- D. The FEX must be exchanged so that it supports the connectivity between fabric interconnects and UCS CSeries servers
Answer: B
NEW QUESTION # 126
Refer to the exhibit. A network engineer is troubleshooting a Cisco Nexus 5000 Series Switch. The interface between the server and the switch is nonoperational and is expected to operate at 10 Gbps. The drain rate of the interface is 3 Mbps. Which action resolves the issue?
- A. Reset priority flow counters
- B. Enable link level pause on the interface
- C. Set priority flow control pause
- D. Configure pause error-disable recovery
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/troubleshooting/guide/ N5K_Troubleshooting_Guide/n5K_ts_fcoe.html
NEW QUESTION # 127
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops.
Which action resolves the issue?
- A. Change the PIN groups on the vHBAs.
- B. Set the FCoE VLAN as the native VLAN on server uplinks.
- C. Modify the VLAN assignment to vNICs.
- D. Modify the FCoE VLAN.
Answer: C
Explanation:
Section: Compute Platforms
NEW QUESTION # 128
Refer to the exhibit. An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used.
Which action resolves the problem?
- A. Configure destination-mac load balancing on N5K-Core-1
- B. Configure source-destination load balancing on N5K-Core-1.
- C. Configure each uplink to be a member of a separate LACP port channel.
- D. Configure the pinning max-link as 2.
Answer: D
Explanation:
https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/n5k/commands/pinning-max-links.html
NEW QUESTION # 129
An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?
- A. Install Server Firmware, then Install Infrastructure Firmware
- B. Install Hypervisor Firmware, then Install Infrastructure Firmware
- C. Install infrastructure Firmware, then Install Hypervisor Firmware.
- D. Install Infrastructure Firmware, then Install Server Firmware.
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2-5/b_GUI_Firmware_Ma
NEW QUESTION # 130
Refer to the exhibit. A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2. The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?
- A. Enable IPv6 routing on R1
- B. Advertise L2VPN EVPN under IPv4 unicast address family
- C. Create a route map that sets the IPv6 next hop.
- D. Configure an IPv6 BGP neighbor on R1
Answer: C
NEW QUESTION # 131
A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?
- A. Verify that the SFPs are supported.
- B. Run the shutdown and then no shutdown command on the interface.
- C. Change the SFP to operate at 4 Gbps instead of 2 Gbps.
- D. Run the switchport ignore bit-errors command on the interface.
Answer: D
NEW QUESTION # 132
Refer to the exhibit. An engineer is troubleshooting a VSAN membership issue on switch N9K_1 where vfc 13 is associated to VSAN 1 instead of VSAN 10. The Cisco UCS, N9K_2, and QoS configurations have been verified. Which additional configuration on N9K_1 must be implemented to resolve the issue?
- A. vlan 10
bind fcoe vsan 10 - B. interface vfc 13
bind fcoe vsan 10 - C. vsan 10 database
bind interface vfc 13 - D. vsan database
vsan 10 interface vfc 13
Answer: D
NEW QUESTION # 133
Refer to the exhibit.
A network engineer is implementing a Cisco UCS environment. The environment consists of eight servers configured with the same service profile template and Windows 2012 installed. The VFC interfaces of five of these servers are showing the error shown in the exhibit. Which action resolves the issue?
- A. Configure upstream zoning
- B. Decommission and recommission the servers
- C. Modify the vHBAs name in the storage connectivity policy
- D. Modify the boot order in the boot policy
Answer: B
NEW QUESTION # 134
Refer to the exhibit.
The integration between Cisco UCS Manager and Cisco UCS Central failed. Which action resolves the issue?
- A. Configure the shared secret key between the appliances
- B. Implement the consistent NTP source between the appliances
- C. Configure the certificate between the appliances
- D. Implement the connectivity between the appliances through a firewall
Answer: B
NEW QUESTION # 135
A mission-critical server is connected to site A.
Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging. Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?
- A. Use the otv isis bfd <> command to configure BFD protocol.
- B. Unknown unicast flooding is not allowed.
- C. Use route-map to advertise this MAC statically and redistribute with ISIS.
- D. Use the otv flood mac <> command to selectively flood traffic for a given MAC.
Answer: D
NEW QUESTION # 136
Refer to the exhibit.
Refer to the exhibit. The monitoring team reports an inability to access the devices after a new centralized management integration. Which action resolves the issue?
- A. Enable SHA authentication for the admin user.
- B. Change the admin user permissions to write.
- C. Update the community string.
- D. Modifly the SNMP ACL to allow the incoming request packets.
Answer: C
NEW QUESTION # 137
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.
Answer:
Explanation:
NEW QUESTION # 138
......
300-615 Study Material, Preparation Guide and PDF Download: https://www.passreview.com/300-615_exam-braindumps.html
Best 300-615 Exam Dumps for the Preparation of Latest Exam Questions: https://drive.google.com/open?id=1c9Ble_S76cBb_RZhVnjCS3-XidpvP8FC