Free Sample Questions to Practice JN0-363 Certification Test Engine [May-2024]
2024 Valid JN0-363 Real Exam Questions, practice JNCIS-SP
One of the unique features of the Juniper JN0-363 is that it emphasizes hands-on knowledge and experience required when working with Juniper Networks technology. This is reflected in the exam format, which includes practical, hands-on exams to simulate real-world scenarios. This hands-on approach to certification ensures that certified professionals are equipped to work in complex networking environments.
NEW QUESTION # 111
What Is a key differentiator of generate routes from aggregate routes?
- A. Generate routes cannot be used as a gateway of last resort.
- B. Generate routes have a default next-hop value of reject.
- C. Generate routes have a default preference value of 210.
- D. Generate routes use a forwarding next hop.
Answer: D
Explanation:
https://www.networkfuntimes.com/junos-aggregate-routes-vs-generate-routes-how-to-summarise-on-juniper-rou Generated routes are a type of route that can be created to summarize and generate more specific routes within the routing table. Unlike aggregate routes, which summarize existing routes and inherit a next-hop, generated routes do not necessarily have to match an existing route and will have a next-hop of reject by default unless specified otherwise.
References
Juniper Networks Technical Documentation on Routing Policies and Route Generation
NEW QUESTION # 112
Exhibit
Which two statements are correct about the service provider MPLS network shown in the exhibit? (Choose two.)
- A. R3 is considered a transit router.
- B. R3 is considered a P router.
- C. R3 is considered an ingress router.
- D. R3 is considered a PE router.
Answer: B,D
NEW QUESTION # 113
Which configuration selling prohibits a static route from being redistributed by a dynamic routing protocol?
- A. passive
- B. qualified-next-hop
- C. route-filter
- D. no-readvertise
Answer: D
NEW QUESTION # 114
Exhibit
Referring to the exhibit, which statement is true about VRRP?
- A. Both routers are in the same state because they have the same VRRP priority.
- B. RRP Is functioning normally in active/active mode.
- C. The routers should use different virtual IP addresses for VRRP to function correctly.
- D. VRRP communication between the two devices is not functioning correctly.
Answer: C
NEW QUESTION # 115
What are three well-known mandatory BGP attributes? (Choose three.)
- A. MED
- B. origin
- C. next hop
- D. AS path
- E. community
Answer: B,C,D
NEW QUESTION # 116
Because of recent network failures, additional circuits have been purchased. In addition, Fast reroute has been configured on critical MPLS LSPs.
When the next failure occurs, which two time intervals will affect fast reroute? (Choose two.)
- A. The amount of time to detect a link or node failure
- B. The amount of time required to recalculate the best detour
- C. The amount of time it takes to ping the gateway on the detour link
- D. The amount of time required to reroute the traffic onto the detour
Answer: A,D
NEW QUESTION # 117
Exhibit
Referring to the exhibit, which two statements are correct? (Choose two.)
- A. Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0M with an outer VLAN tag of 200.
- B. Traffic ingressing ge-0/0/0 that is tagged will VLAN 100 will be dropped.
- C. Traffic ingressing ge0/0/0 that Is tagged with VLAN 200 will egress ge-0/0/1 with an outer VLAN tag of 200.
- D. Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.
Answer: B,D
NEW QUESTION # 118
What are two valid next-hop types that would be configured for a static route? (Choose two.)
- A. An egress interface name
- B. An igress interface name
- C. A MAC address
- D. An IP address
Answer: A,D
NEW QUESTION # 119
Click the Exhibit button.
You are asked to configure OSPF for the network?
Referring to the exhibit, how should Area 1 be configured?
- A. not-so-stubby area
- B. totally stubby area
- C. backbone area
- D. stub area
Answer: D
Explanation:
https://www.juniper.net/documentation/en_US/junos/topics/topic-map/configuring-ospf-areas.html
NEW QUESTION # 120
Click the Exhibit button.
Referring to the exhibit, you have an established RSVP LSP between R1 and R4 when you experience a link failure between R2 and R3.
Which two statements are correct? (Choose two.)
- A. R2 sends a PathTear message upstream to R1 signaling the link failure.
- B. R2 sends a ResvTear message upstream to R1 signaling the link failure.
- C. R3 sends a PathTear message downstream to R4 signaling the link failure.
- D. R3 sends a ResvTear message downstream to R4 signaling the link failure.
Answer: B,D
Explanation:
Upon a link failure in an RSVP-signaled LSP, the router upstream of the failure (R2) sends a PathTear message upstream to the ingress router (R1), and the router downstream of the failure (R3) sends a ResvTear message downstream to the egress router (R4). These messages signal the failure and initiate tear down of the LSP state in the respective directions.References:
RSVP-TE Overview, Juniper Networks Documentation
Understanding RSVP Signal Failures, Juniper Networks Documentation
NEW QUESTION # 121
Which two statements are correct about IS-IS? (Choose two.)
- A. A level 1 only router can form an adjacency with a level 2 only router.
- B. For level 2 adjacencies, the area IDs can be different.
- C. A level 1 only router can never form an adjacency with a level 2 only router.
- D. For level 2 adjacencies, the area IDs must be the same.
Answer: A,D
NEW QUESTION # 122
Which two problems occur when increasing numbers of users are added to an Ethernet LAN with no switches present? (Choose two.)
- A. There is a greater chance for collisions to occur
- B. There is unnecessary consumption of network bandwidth
- C. Some devices will not see certain traffic
- D. The MAC table sizes increase
Answer: A,B
NEW QUESTION # 123
Exhibit.
Referring to the exhibit, you have configured an aggregate route that represents the 172.21.0.0/24,
172.21.1.0/24, and 172.21.2.0/24 networks. However, when you view the routing table, your new route hidden.
Which action would you perform to determine the problem?
- A. Verify that you have configured a policy on the device to accept aggregate routes.
- B. Verify that you have defined a metric value for the aggregate route.
- C. Verify that you have set the preference to a lower default value.
- D. Verify that you have active contributing routes on the device.
Answer: C
Explanation:
The exhibit shows an aggregate route configuration for the network172.21.0.0/22, which would summarize the specific networks172.21.0.0/24,172.21.1.0/24, and172.21.2.0/24. For an aggregate route to be active, it must have contributing routes in the routing table. If the route is hidden, it usually means there are no contributing routes that are active or the policy applied to the aggregate does not match any of the specific routes.Therefore, the first step in troubleshooting would be to verify that there are indeed active contributing routes for the aggregate to be valid.
References:
Juniper documentation on routing policies and aggregates: Junos OS Routing Policies, Firewall Filters, and Traffic Policers User Guide
NEW QUESTION # 124
Click the Exhibit button.
In the network shown in the exhibit, all switches are configured with the default STP root bridge priority, and Switch A has been selected as root. You recently added the older Switch D into the network as an access switch, and notice it has taken over as root.
Which configuration would solve this problem?
- A.
- B.
- C.
- D.
Answer: D
Explanation:
https://www.juniper.net/documentation/en_US/junos/topics/reference/configuration-statement/no-root-port-edit-protocols-stp.html
NEW QUESTION # 125
Click the Exhibit button.
Referring to the exhibit, which statement is correct?
- A. Interface xe-0/0/0.0 has a default metric of 10
- B. Interface ge-1/0/0.0 can only form a single adjacency
- C. Interface ge-3/0/0.0 has a default metric of 10
- D. Interface xe-0/0/0.0 can only form a single adjacency
Answer: B
NEW QUESTION # 126
......
Genuine JN0-363 Exam Dumps Free Demo Valid QA's: https://www.passreview.com/JN0-363_exam-braindumps.html
Latest Success Metrics For Actual JN0-363 Exam (Updated 293 Questions): https://drive.google.com/open?id=1SNaY4ipHRaq9lxicuDWsU9cggJhg9OoM