[2021] 300-625 PDF Questions - Perfect Prospect To Go With PassReview Practice Exam
Cisco 300-625 Pdf Questions - Outstanding Practice To your Exam
NEW QUESTION 32
Which condition requires using a device alias rather than a Fibre Channel alias?
- A. Aliases must be saved within a central database on the fabric.
- B. All aliases being used are being configured in the same VSAN.
- C. The zone database must be distributed over the fabric.
- D. The same alias must be used in zoning as well as DPVM.
Answer: C
NEW QUESTION 33
The principal switch on a Fibre Channel network fails to assign requested domain to a subordinate switch.
What are two reasons? (Choose two.)
- A. The requested domain is outside the allowed list.
- B. Cisco Fabric Services distribution is not enabled on the switch.
- C. The fabric is locked.
- D. The persistent FC ID feature is not enabled.
- E. An existing switch already has the requested domain assigned.
Answer: A,E
NEW QUESTION 34
Drag and drop the items from the left onto the correct descriptions on the right. Not all items are used.
Answer:
Explanation:
NEW QUESTION 35
What does an unlicensed DCNM SAN fail to display?
- A. Fibre Channel, FCoE, and iSCSI topologies
- B. historical performance monitoring
- C. real-time performance monitoring
- D. events and fault management
Answer: B
NEW QUESTION 36
Which item is a component of Cisco DCNM?
- A. Cisco DCNM FabricPath license
- B. Cisco DCNM for B- and C-Series servers
- C. Cisco DCNM for SAN and Cisco DCNM for LAN
- D. Cisco DCNM for Cisco UCS Manager
Answer: C
NEW QUESTION 37
Which result occurs when a VSAN is deleted that contains non-trunking ports?
- A. The ports are moved to VSAN 4094.
- B. The ports are removed from the configuration.
- C. The port configurations are cleared.
- D. The ports are moved to VSAN 1.
Answer: A
Explanation:
Section: Implementation
NEW QUESTION 38
After a subordinate switch requests a domain ID form a principal switch, the requested domain ID becomes the runtime domain ID, and all interfaces on the affected VSAN are isolated. What is a solution to the issue?
- A. Configure a static domain on the subordinate switch and reboot the switch.
- B. Configure IVR NAT on the affected VSAN.
- C. Enable the FICON feature on the affected VSAN.
- D. Add the received ID to the allowed list.
Answer: D
NEW QUESTION 39
Refer to the exhibit.
A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS 9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)
- A. Add dst-grp 300 under subscription 200.
- B. Add dst-grp 100 under subscription 200.
- C. Add dst-grp 200 under subscription 100.
- D. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.
- E. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 300.
Answer: C,D
NEW QUESTION 40
A storage network engineer is upgrading a Cisco MDS Director with dual supervisor modules. The install command is executed on the standby supervisor module but fails. Which action would have prevented this failure?
- A. Fabric Controller Service must be stopped before starting the upgrade.
- B. Cisco Fabric Services must be disabled before starting the upgrade.
- C. All FCoE interfaces configured on the MDS must be shut down before starting the upgrade.
- D. The upgrade must be done on the active supervisor module only.
Answer: D
NEW QUESTION 41
Which result occurs if a device alias is renamed and then the original device alias name is used in an add command in the same session?
- A. The rename command is moved to the rejected list and the add command executes successfully.
- B. The device alias is renamed and the add command is moved to the rejected list.
- C. Both commands execute successfully.
- D. Both commands are moved to the rejected list.
Answer: C
Explanation:
Section: Implementation
NEW QUESTION 42
Which configuration is available only in Cisco DCNM-SAN Advanced mode?
- A. zoning
- B. VMpath configuration
- C. template-based provisioning
- D. IVR
Answer: D
Explanation:
Section: Deployment
NEW QUESTION 43
DRAG DROP
Drag and drop the boot issues from the left onto the correct solutions on the right.
Select and Place:
Answer:
Explanation:
Section: MDS Troubleshooting
Explanation
NEW QUESTION 44
A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?
- A. show telemetry transport
- B. show telemetry control stats
- C. show telemetry pipeline stats
- D. show analytics system-load
Answer: A
NEW QUESTION 45
Which statement accurately describes the result of disabling restrictions on oversubscription ratios on Cisco MDS 9000 Series Fibre Channel switching modules?
- A. The bandwidth allocated to shared ports is proportionate to the configured speed of the ports.
- B. The bandwidth allocation of the shared ports is equal to the lowest configured bandwidth.
- C. A port-group can contain a single port only.
- D. QoS can be configured.
Answer: A
NEW QUESTION 46
Refer to the exhibit.
Refer to the exhibit. A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?
- A. Hard zoning is enabled
- B. Merge control is disabled
- C. The fabric is locked by admin on another switch
- D. The fabric is locked by admin on switch-2
- E. The switch has a conflicting domain ID
Answer: C,E
NEW QUESTION 47
An engineer is configuring a SAN environment and attempts to activate a zoneset, but a lock is held by another user. Which argument does the engineer use to clear the lock from the zoning database configuration?
- A. abort
- B. commit
- C. force
- D. clear
Answer: D
NEW QUESTION 48
A storage network engineer must configure a 48-port Cisco MDS switch to reject any login requests to VSAN 10 from unauthorized Fibre Channel devices and switches. All the devices that were already logged in to the switch from this VSAN must be allowed without any manual configuration. Which configuration must be applied?
- A. switch(config)# feature port-security
switch(config)# port-security activate vsan 10 no auto-learn - B. switch(config)# port-security activate vsan 10
- C. switch(config)# feature port-security
switch(config)# port-security database vsan 10
switch(config-port-security)# any-wwn interface fc1/1 - fc1/48 - D. switch(config)# feature port-security
switch(config)# port-security activate vsan 10
Answer: B
NEW QUESTION 49
......
Online Questions - Outstanding Practice To your 300-625 Exam: https://www.passreview.com/300-625_exam-braindumps.html